CONTROL CONSOLES & DIMMERS
DMXAC8
DMXAC8Availability: 
A-000000-05931
EAN code: 4052809230641
DMXREC
DMXRECAvailability: 
A-000000-05912
EAN code: 4052809230245
It is probably THE solution for installations and distributors: the “DMXREC” from INVOLIGHT. The principle sounds simple – and is it: The “DMXREC” is a DMX recorder that can record complex scenes no matter what they were created with. And that across the entire spectrum of a DMX universe, ie 512 channels. Afterwards, up to 7 shows can be conveniently selected and played back via the “RECPanel” control panel or via the recorder itself. In practice, this is also very easy to implement: Create as usual with your DMX controller or DMX software scenes or shows. Then connect the controller or the software interface with the “DMXREC”. This switch to “Record” and play back your created shows. The “DMXREC” records these values and saves them. There are 7 memory slots available. If all scenes and shows have been recorded by the “DMXREC”, you can play them back with the “Play” button and also adjust their speed. The “DMXREC” plays the selected show in an endless loop, so that no interruptions take place. The optically very noble “RECPanel” is intended for wall mounting. It can be installed discreetly in catering establishments in areas accessible to personnel. The connection between the recorder and the panel is realized with a simple network cable that can be conveniently purchased in the desired length in any electrical market. For lenders, perhaps even the recorder is enough, which is why the two items from this set are also available separately. We recommend this innovative solution especially for catering establishments, where the staff should start and stop shows without prior knowledge and for lenders who want to prevent stored scenes or shows from being altered or even deleted accidentally.
DMXREC512
DMXREC512Availability:
A-000000-06047
EAN code: 4052809230306
With the DMX REC512, you can play pre-made programs without the DMX console. Program speed can be set on “DMXREC512”, 7 buttons for direct selection of programs, Dim button
DMXS4
DMXS4Availability:
A-000000-05906
EAN code: 4052809230269
The “DMXS4” from INVOLIGHT is a splitter and repeater. It offers four 3-pin XLR outputs to split the DMX signal on larger setups and installations. This device receives the incoming DMX signal and distributes it to 4 separate outputs. This reduces problems with ground loops and amplifies the DMX signal. All outputs include 3-pin XLR jacks that are electronically isolated to ensure uninterrupted data flow. 4 green control LEDs indicate that everything is ok and the outputs are ready. In addition, each output has dedicated drivers to amplify the incoming signal.
DMXS6
DMXS6Availability:
A-000000-05907
EAN code: 4052809230276
The “DMXS6” by INVOLIGHT is a professional splitter and repeater for direct truss assembly with Velcro. It offers six 3-pin XLR outputs for dividing the DMX signal in complex setups and installations. This device receives the incoming DMX signal and distributes it to 6 separate outputs. This reduces problems with ground loops and amplifies the DMX signal. All outputs include 3-pin XLR jacks that are electronically isolated to ensure uninterrupted data flow. The switchable 120 Ohm terminator for the DMX Link-Out is also extremely useful. If this is not required, the terminal resistor can be connected to prevent interference. Each output has a red and green control LED. These signals whether everything is OK (green) or a fault (red). In addition, each output has dedicated drivers to amplify the incoming signal.
DMXS8
DMXS8Availability:
A-000000-05908
EAN code: 4052809230283
The “DMXS8″ by INVOLIGHT is a splitter and repeater in 19 ” format. It offers eight 3-pin XLR outputs for dividing the DMX signal in complex setups and installations. This device receives the incoming DMX signal and distributes it to 8 separate outputs. This reduces problems with ground loops and amplifies the DMX signal. All outputs include 3-pin XLR jacks that are electronically isolated to ensure uninterrupted data flow. The switchable 120 Ohm terminator for the DMX Link-Out is also extremely useful. If it is not needed, the end resistor can be connected to prevent interference. Each output has a red and green control LED. These signals whether everything is OK (green) or a fault (red). In addition, each output has dedicated drivers to amplify the incoming signal.
EASYCONTROL
EASYCONTROLAvailability:
A-000000-05904
EAN code: 4052809230221
LEDCONTROL
LEDCONTROLAvailability: 
A-000000-05911
EAN code: 4052809230191
LIGHTCONTROL
LIGHTCONTROLAvailability:
A-000000-05910
EAN code: 4052809230214
The completely new “COMMANDER” series from INVOLIGHT includes a variety of newly developed DMX control devices for a wide range of applications. The series offers controllers for e.g. LED spotlights, scanners, moving heads and other DMX-controllable devices. They were all designed with the latest know-how and innovative ideas and offer a correspondingly high level of user-friendliness. Particular attention was paid to simple, quick-to-learn operation. All controllers are delivered with detailed, clearly understandable operating instructions in German and English so that the user can quickly understand the console and use it professionally. The “LIGHTControl” is a lavishly equipped chaser console with a control capacity of up to 16 devices, each with up to 18 channels. It has 16 channel strips and a joystick, allowing access to all channels instantly and without scrolling through multiple pages. A particularly noteworthy innovation is the “preset function”, with which you can define and name 16 channels for specific functions. The function is then shown in the display when you slide the control (e.g. channel strip 5 for “Goborad” – “GOBO” is shown in the display). This eliminates the often annoying “guessing” of which function is currently being controlled. In addition, channel 16 can be made additional to the master dimmer, which is always useful if devices do not have one. Each channel fader can also be assigned to any DMX channel. For example, if you are used to a certain function being on a certain channel, but this is not the case with the device you want to control, you can simply reassign the channel. The PAN/TILT joystick can also be freely assigned and does not necessarily have to be used for PAN/TILT. Thanks to the freely assignable special buttons AUX1 and AUX2, strobes and fog machines, for example, can be operated at the push of a button. There is also plenty of storage space when it comes to programming. 30 scenes and 30 chases can be saved. The chases can each be made up of up to 200 scenes. All saved sequences can then either be called up manually or played as an automatic program with adjustable speed or in music-controlled mode. Thanks to MIDI compatibility, it is also possible to control the device via a keyboard or sequencer software. The USB port is also particularly noteworthy. Shows or individual scenes can be saved here on USB sticks and read back in if data is lost.
RECPANEL
RECPANELAvailability:
A-000000-05915
EAN code: 4052809230291
The visually very elegant “RECPanel” is intended for wall mounting and is used to operate the DMXREC via touch pad control. It can be discreetly installed in areas accessible to personnel during installations. The connection between the recorder and the panel is made with a simple network cable (not included).
RECPANEL512
RECPANEL512Availability:
A-000000-06048
EAN code: 4052809230313
SCANCONTROL
SCANCONTROLAvailability:
A-000000-05905
EAN code: 4052809230238
